E和Qtopia过程

Linux系统是完全安装RedHat9.0，板子是hybus的X-Hyper250B的，Toolchain用的是开发板带的hybus-arm-linux-R1.1（库的版本是2.95.3）交叉编译所用到的文件：（所有文件都放在/usr/local/下面）qt-embedded-2.3.10-free.tar.gzqt-x11-2.3.2.tar.gzqtopia-free-source-2.1.1.tar.gztmake-1.13.tar.gze2fsprogs-1.35.tar.gzl主机x86的编译步骤：tar xfz qt-embedded-2.3.10-free.tar.gz（解压后qt-2.3.10改名为qt-2.3.10-host）export QTEDIR=$PWD/qt-2.3.10-hosttar xfz qt-x11-2.3.2.tar.gz（解压后为qt-2.3.2）export QT2DIR=$PWD/qt-2.3.2tar xfz qtopia-free-source-2.1.1.tar.gz（解压后qtopia-free-2.1.1改名为qtopia-2.1.1-host）export QPEDIR=$PWD/qtopia-2.1.1-hosttar xfz tmake-1.13.tar.gz（解压后tmake-1.13）export TMAKEDIR=$PWD/tmake-1.13export TMAKEPATH=$PWD/tmake-1.13/lib/qws/linux-x86-g++export PATH=$TMAKEDIR/bin:$PATHcd qt-2.3.2export QTDIR=$QT2DIRexport PATH=$QTDIR/bin:$PATHexport LD_LIBRARY_PATH=$QTDIR/lib:$LD_LIBRARY_PATH./configure -no-xftmakemake -C tools/qvfbcd ..cd qt-2.3.10-hostexport QTDIR=$PWDexport PATH=$QTDIR/bin:$PATHexport LD_LIBRARY_PATH=$QTDIR/lib:$LD_LIBRARY_PATHmkdir bin （因为解压后的qt-2.3.10没有bin文件夹）cp $QT2DIR/bin/uic bincp $QT2DIR/tools/qvfb/qvfb bincp $QPEDIR/src/qt/qconfig-qpe.h src/tools/./configure -qconfig qpe -qvfb -thread -system-jpeg -gif -depths 4,8,16,32makecd ..tar xzf e2fsprogs-1.35.tar.gzcd e2fsprogs-1.35./configure -enable-elf-shlibsmake install lib/uuid/注：这是编译x86的libuuid库cd ..cd qtopia-2.1.1-hostexport PATH=$QPEDIR/bin:$PATHexport LD_LIBRARY_PATH=$QPEDIR/lib:$LD_LIBRARY_PATH./configuremake编译例子：（注意：环境变量要按照上面export设置）$qmake -project ==>>我都是这样创建.pro文件的$tmake -o Makefile hello.pro$make$qvfb &$./hello -qws 或者$qpe还没怎么仔细研究过qpe。l 目标机arm的编译步骤：tar xfz qt-embedded-2.3.10-free.tar.gz（解压后qt-2.3.10改名为qt-2.3.10-target）export QTEDIR=$PWD/qt-2.3.10-targettar xfz qt-x11-2.3.2.tar.gzexport QT2DIR=$PWD/qt-2.3.2tar xfz qtopia-free-source-2.1.1.tar.gz（解压后qtopia-free-2.1.1改名为qtopia-2.1.1-target）export QPEDIR=$PWD/qtopia-2.1.1-targettar xfz tmake-1.13.tar.gzexport TMAKEDIR=$PWD/tmake-1.13export TMAKEPATH=$PWD/tmake-1.13/lib/qws/linux-arm-g++export PATH=$TMAKEDIR/bin:$PATHcd qt-2.3.2export QTDIR=$QT2DIRexport PATH=$QTDIR/bin:$PATHexport LD_LIBRARY_PATH=$QTDIR/lib:$LD_LIBRARY_PATH./configure -no-xftmakemake -C tools/qvfbcd ..cd qt-2.3.10-targetexport QTDIR=$PWDexport PATH=$QTDIR/bin:$PATHexport LD_LIBRARY_PATH=$QTDIR/lib:$LD_LIBRARY_PATHmkdir bincp $QT2DIR/bin/uic bincp $QT2DIR/tools/qvfb/qvfb bincp $QPEDIR/src/qt/qconfig-qpe.h src/tools/./configure -xplatform linux-arm-g++ -qconfig qpe -qvfb -thread -system-jpeg -gif -depths 4,8,16,32makecd ..注：这里交叉编译arm版本的Qt/E，需要arm版本的libjpeg.so.62，hybus-arm-linux-R1.1里面包含这个库;如没有可以上网下载。tar xzf e2fsprogs-1.35.tar.gzcd e2fsprogs-1.35./configure -host=arm-linux -with-cc=arm-linux-gcc -with-linker=arm-linux-ld -enable-elf-shlibs -prefix=/usr/local/hybus-arm-linux-R1.1/arm-linuxmake install lib/uuid/ ===>>>这步安装到hybus-arm-linux-R1.1/lib上的libuuid.so.1.2版本不对,要执行cp lib/libuuid.so.1.2 ../hybus-arm-linux-R1.1/lib注：这步是交叉编译libuuid库，配置详情见./configure --help（多谢http:/panjet.wleda.com/？p=20里面的大哥呀）cd ..cd qtopia-2.1.1-hostexport PATH=$QPEDIR/bin:$PATHexport LD_LIBRARY_PATH=$QPEDIR/lib:$LD_LIBRARY_PATHcp src/libraries/qtopia/custom-linux-ipaq-g++.cpp src/libraries/qtopia/custom-linux-arm-g++.cppcp src/libraries/qtopia/custom-linux-ipaq-g++.h src/libraries/qtopia/custom-linux-arm-g++.h./configure -xplatform linux-arm-g++make注：这里需要libstdc++.so和libgcc_s.so库，hybus-arm-linux-R1.1/lib没有，所以要从网上下载;版本一定要是2.95.3。